Edimax-technology WP-S1300 Manuel d'utilisateur

Back Name Description Reset When this projector server is not working properly, you can use a pen or pin to press and hold this button for 5 se

Remote Control - Front Name Description „Black out‟ Button Press this button to activate „Black Out‟ function, which will remove any display c

Remote Control - Top Name Description IR Transmitter Infrared signal transmitter. When using the remote Control, point t

Remote Control - Back Name Description Battery Lid Press battery lid and push it out to open battery compartment (to i

1-6 Install Wireless Projector Server Please follow the following instructions to get the projector server installed: 1. Unpack the wireless project

You can skip this step if you don’t have external audio amplifier / speaker. 5. Insert VGA cable which connects with external video display to VGA

at the back of projector server. 9. Press „Power‟ button located at the front of projector server. 10. Open battery lid located at the back of re

Chapter II Using Projector Server 2-1 Switch the Projector Server On and Check IP address When the connection between projector server and external

When the projector server is powered on and connected to a LAN with DHCP server, it will get an IP address from DHCP server automatically; when there‟

2-2 Connect to Projector Server by Wireless Ethernet The wireless Ethernet interface of this projector server is switched on and accepts any computer

Table of Contents Chapter I Product Introduction ... 4 1-1 Package Con

2-3 Set the IP address of the Computer If there‟s no DHCP server available on your LAN, please follow the following instructions to set the IP addres

2. Select „Specify an IP address‟, then input the following settings in respective field: IP address: 192.168.2.x (where x is an integer greater or

2-3-2 Windows 2000 IP address setup: 1. Click „Start‟ button (it should be located at lower-left corner of your computer), then click control pane

2. Select „Use the following IP address‟, then input the following settings in respective field: IP address: 192.168.2.x (where x is an integer gre

2-3-3 Windows XP IP address setup: 1. Click „Start‟ button (it should be located at lower-left corner of your computer), then click control panel.

2. Select „Use the following IP address‟, then input the following settings in respective field: IP address: 192.168.2.x (where x is an integer gre

2-3-4 Windows Vista IP address setup: 1. Click „Start‟ button (it should be located at lower-left corner of your computer), then click control pan

2. Select „Use the following IP address‟, then input the following settings in respective field: IP address: 192.168.2.x (where x is an integer gre

2-4 Download and Install Client Software Before any computer can use the projector server, client software must be installed first. Please follow the

3-5-1 ‘Basic’ Settings ... 63 3-5-2 ‘Advanced’ Settings ...

2. If you just want to display image on projector and don‟t want to install software on your computer (especially when you‟re a guest and only need to

4. Click „Run‟ to start software installation: 5. Please click „Next‟ when you‟re prompted, until installation procedure is complete.

If you see this warning message, please click „Continue Anyway‟ to continue, or installation cannot be completed (You may see this message appear for

2-5 Connect to Projector Server To connect to projector server, click „Start‟ in projector server‟s web page: You‟ll be prompted to save or run pr

If you have personal firewall software installed, or you‟re using Windows XP / Vista operating system, you may see similar message windows appear:

server‟s display, and login code can be found at lower-right corner: Please input a unique user name (used to identify each projector server user a

If the login code you provided is not the same with projector server‟s displayed login code, the following message will appear: If you see this mes

If you entered correct login code, you‟ll be connected to projector server as one of users, and the client software will be look like this: Before

You can click „Start / Stop‟ button (as indicated above) to start presentation (the content of your computer‟s display will be transmitted to proje

Chapter I Product Introduction 1-1 Package Contents Thank you for purchasing this wireless projector server! Before you start to use this product, p

2-6 Using Client Software If you download and execute client software, the client software will appear instantly, you don‟t have to install the softw

After Login: Close Application Minimize Client Software Play / Stop 1/2/3/4 Quad-Split Image Quality Setup

2-6-1 Client software icon After you connected to projector server and start transmitting display content, an icon will appear beside the clock of sy

Sound Sound of your computer will be transmitted to projector server by default. If you don‟t want to transmit the sound of your computer to projec

2-6-2 Start / Stop Projection To start / stop projection (display the display content of your computer to projector), simply click „Start / Stop‟ but

2-6-3 Quad-split Display This projector server supports quad-split projector display which allows maximum 4 users to display their computer‟s display

2-6-4 Change Display Setting The image displaying speed of different computer may vary depends on the network connection speed and other factors. If

2-7 Broadcast With this function, You can broadcast some specific content to more than one Projector Servers on your network. To activate broadcast f

NOTE: ‧Broadcast will not work when doing the presentation. Please stop the presentation before use 2-8 Capture Display To display a specific ar

player. Set: Select “Set” to confirm the frame of the player for projection. Close: To unlock the frame of your player for projection. Select Area Sel

1-2 Safety Instructions Please follow the following safety instructions when you‟re using this wireless projector server, or you may damage this proj

2-10 Using Remote Control When the presentation is in progress, you can use supplied remote Control to control the presentation. When using remote Co

2-11 Select User When there‟re more than one connected client software, project server can select one of them to display its display content. In the

In this example, total 2 users are connected. You can press „User Switch‟ button to select which user should projector server display its display c

2-11-2 Use Remote Control You can also use remote Control to select which user should projector server display its display content: 1. If there‟s a

Chapter III Configure Projector Server 3-1 Connect to Web Configuration Menu This projector server provides several administrative functions which c

2. Click „Admin Login‟ link on the left. 3. You‟ll be prompted to input administrator‟s username and password. Default „User Name‟ is „admin‟ and „

4. After you logged in, the status of projector server will be shown on web browser.

3-2 Utility Download You can use this function to download projector server‟s client software. (Same as described in chapter 2-4) Click ‘Start’ l

3-3 Basic Setting In this menu, you can change web configuration menu password. You can use this function to change the password required for logg

Click „Continue‟ to continue on projector server setting, or click „Apply‟ to reboot projector server, and changes you made will take effect after p

10. There‟s no user-serviceable part inside this wireless projector server; if the wireless projector server is not working properly, please contact t

3-4 Network Setting You can use this menu to change the setting of wired Ethernet connection and DNS (Domain Name Service) server. The description

is not located within local area network, projector server will not be able to access Internet and synchronize with time server. DNS address Input the

3-5 Wireless Setting You can configure the settings of the wireless network interface of this projector server from this menu.

3-5-1 ‘Basic’ Settings You can configure basic wireless network settings from this menu. The description of every setting item will be described

wireless clients. 2.4GHz (G) - supports 802.11g wireless clients only. 2.4GHz (B+G+N) - supports 802.11b, 802.11g, and 802.11 Draft-n wireless client

discard changes, click „Cancel‟ button. If you click „Apply‟, you‟ll see the following message: Click „Continue‟ to continue on projector server s

3-5-2 ‘Advanced’ Settings In this menu, you can configure advanced wireless settings of this projector server. Please note that only experienced user

default value if you don’t know what it is, default value is 2347. Beacon Interval Set the beacon interval of wireless radio. Do not modify default va

‘Enable’. WMM The short of Wi-Fi MultiMedia, it will enhance the data transfer performance of multimedia contents when they‟re being transferred over

3-5-3 ‘Security’ Settings In this menu, you can setup wireless security for wireless connections. By default, projector server does not enable wir

1-3 System Requirements Video Display: A Projector, CRT display, LCD display, or plasma TV that support VGA video input. The display should sup

almost every wireless client support WEP (especially some old IEEE 802.11b wireless clients), therefore WEP provides better compatibility. Refer to ch

3-5-3-1 Encryption: Disabled When encryption setting is disabled, projector server‟s wireless interface uses no protection against wireless users who

Click „Continue‟ to continue on projector server setting, or click „Apply‟ to reboot projector server, and changes you made will take effect after p

3-5-3-2 Encryption: WEP Enable WEP encryption. The description of every setting item will be described below: Item Description Key Length There a

Encryption Key 1 to 4 Input WEP key characters here, the number of characters must be the same as the number displayed at „Key Format‟ field. You can

3-5-3-3 Encryption: WPA pre-shared key Enable WPA pre-shared key encryption. The description of every setting item will be described below: Item

Click „Continue‟ to continue on projector server setting, or click „Apply‟ to reboot projector server, and changes you made will take effect after p

3-5-3-4 ‘WPS’ Settings In this menu, you can use WPS (Wi-Fi Protected Setup) to setup secure wireless connections quickly and easily with WPS-compati

The description of every setting item will be described below: Item Description Config Mode Select WPS configuration mode: „Registrar‟ (This projec

3-6 Presentation Control You can use this menu to control every connected user, and device who should be active presenter here. The description of

1-4 Highlights of this Wireless Projector Server Thanks again for choosing this wireless projector server. This projector server eases the procedure

You can arrange a specific user to display in quad-split display (1, 2, 3, or 4), or display in full-screen mode: Quad-Split Display (Position 1 /

3-7 Display Setting You can configure the characteristics of external display here. The description of every setting item will be described below:

server rebooted.

3-7 Black Out When you don‟t want audience see the content of your computer display temporarily when you‟re active presenter, you can suspend video o

3-6 Configuration Tools This menu provides several useful functions, you can save projector server‟s configuration (backup), upgrade firmware (to imp

Item Description Backup Settings Click „Save…‟ button to save projector server‟s current setting as a file and store it on your computer. You‟ll be p

3-6-2 Firmware Upgrade In this menu, you can upgrade the firmware of this projector server. New firmware will provide more functionality, and fix som

projector server off during firmware upgrade procedure. Also, please do not remove the network connection during firmware upgrade, if firmware upgrade

3-6-3 Reset If you found that projector server is not function properly, or respond to your command slowly, reboot the projector server may solve the

Chapter IV Appendix 4-1 Hardware Specification  Supports DHCP Server & Client  Supports wireless AP Mode  Download utility from the dev

1-5 Familiar with Wireless Projector Server / Remote Control Front Name Description Power Press this button to switch this projector

Dimension 30(H) x 157(W) x 127(D) mm Temperature Operating: 10~40oC, Storage: -20~60oC Humidity Operating: 10~90% (Non-Condensing) Storage: Ma

4-2 Troubleshooting Don‟t panic if projector server is not function properly! In most cases, you can solve the problem by yourself and you don‟t have

as „Remote‟) is not blocked by any object, especially when you inserted USB peripheral in front USB slot. 4. If there‟s strong / fluorescent light so

Windows system 2. Make sure no one is doing the presentation. 3. Please access to the disk “dPresenter” from “COMPUTER” and execute “dPresenter.exe